Netbackup error san status 23. Netbackup Status Code 23 : Socket Read Failed

Netbackup error san status 23 Rating: 7,8/10 352 reviews

Five Symantec NetBackup error messages and how to resolve them

netbackup error san status 23

Compare configurations The Compare Configurations feature lets you compare different system scans by the data collector. Along with 12 and 24, this helps quick recovery. On Sun Solaris systems you must first verify that all operating systems patches are installed. Do your homework, there are caveats. Hi folks, Back again with my problems! Use tar or Windows backup, or even a rusty abacus, go to your corner and be quiet.

Next

NBD/SAN Transport issues

netbackup error san status 23

There are some specific Symantec commands which are very common and are mostly used both in Windows and Unix. You can also proceed even if you do get this message. If anyone cares then post a comment and I will expand on it. If a job is going to take less than 10min send it to disk. I had forgot to mention that we did have Norton Anti-Virus installed, and it was trying to scan all network traffic, we disabled it, but no difference in speeds were noticed. Sometimes you will get the above screenshot when adding virtual machines. Just have a copy on disk and 2 on tape you can do the ones on tape inline, will create 2 at the same time, it works , then send the ones on tape to 2 different offsite locations.

Next

Netbackup Status Code 23 : Socket Read Failed

netbackup error san status 23

The -p option is required for an immediate-manual backup -i option. There are a couple of things you can do in this situation. Perfectly legitimate commands will not function as you might think due to silly heuristics or lack thereof. Save configurations After logging in, you can retrieve past reports, share reports with colleagues, review notifications you received, and retain custom settings. Original group was on the 192.

Next

Status Code 23 “Socket Read Failed”

netbackup error san status 23

Before presenting these volumes to the Windows server, you must instruct Windows to not automount disks, as this could potentially cause issues with the volumes that contain your virtual machines. Visit Symantec's website to read its. NetBackup status code: 1 Message: The requested action was partially successful In my opinion, this is one of the most frustrating NetBackup status codes. The following commands can be used to test the short name alias and the fully qualified long nameof the system. Also, I ran again a bpcd command form the client, and I get this: 18:58:41.

Next

Error code 230

netbackup error san status 23

Elaborate and numerous policies are more ways to invite uncle Murphy. Remote media servers on the other side of a firewall are a pain, and depending on the circumstances are a necessary evil. NetBackup status code: 12 Message: File open failed This NetBackup status code sounds like a read error, but it occurs when a disk storage unit attempts to write data to the root device of the , which can also happen with media servers. I ran a different backup job on the same volume where the folder size was very small. I especially like your self-description for hitman purposes…. I realize the issue is likely more to do with the network speed than the disk, but this could be part of the issue too? The master server is running on Redhat Netbackup version is 7.

Next

How to configure NetBackup policy to backup VMware VMs

netbackup error san status 23

Also corrupt binaries are one possible cause for this error. In some cases, 1,023-character file paths are allowed, but try to keep the path under 1,000 characters if possible. In addition, you can create system-specific notifications customized to your environment. For the different between the two, please see the section entitled Introduction to Symantec NetBackup 7 located at the beginning of this guide. Example: Use below command to list all the netbackup processes. You may have to do some tweaking in windows to make it really take the 256K blocksize. It takes almost 36 hours to backup.

Next

Most used Netbackup Commands

netbackup error san status 23

You should begin the troubleshooting process by checking the logs for any further explanation of why the restore failed. I am considering putting an interface to 192. The symantec support told me that the netbackup version is not compatible with vmware vcenter 5. It is possible that updates have been made to the original version after this document was translated and published. Description of Change Date NetBackup Version Start of Support Added support for vSphere 6. If it seems that 32 and 33 are somewhat self-contradictory, give yourself a cigar.

Next

STATUS CODE 23: Schedule initiated Client backups fail with a NetBackup Status Code 23 (socket read failed).

netbackup error san status 23

Then, retry the operation and check the resulting debug log. Do you know how to fix problem with orphaned snapshots? What tape drives are you using? Most used NetBackup Commands Below is the list of Netbackup commands which are used mostly in Windows and Unix platform. They servers are segregated for security reasons. As long as the backup started during the start window, they can continue to run outside of the window eg: if the backups take that long or if there was some kind of problem that delayed the backups from running. Solution For both Backup and Restore operations, NetBackup and Backup Exec allow choosing any of the four transport modes or a combination of these. Client process aborted error 50. But intelligent disk layouts are necessary.

Next